The Alterna Jar is basically made to fit 2 different type of blenders. One is the Blendtec blender series. The other is the 'other' blender group, which is basically all the same, when it comes to blender jar compatibility.
They all fit on each others' blender platform, in other words. These are the Waring 3.5 hp blenders (not anything else from Waring), the Vita Mix type blenders, the Omni by JTC, and all their associated private label brands - all the same, basically, when it comes to their jars fitting onto one and the other blender.
The Blendtec blenders' motor turns clockwise and the Blendtec blender base comes with a drive socket attached to the motor axle permanently, metal on metal, no clutch. A clutch would be a way out to absorb energy (bad energy that could break the motor). And the Blendtec blender jars have permanently installed blades that cannot be removed, taken out without breaking the jar and/or the blade bearing assembly, and the blades are not sharp either.
As a matter of fact, Blendtec apparently insists that their blades perform better dull than any other sharpened blades / knives. The only beef with that is however that a dull sword does not cut off heads as easy or as clean as a sword that has a very sharp edge. Also a dull shear machine, if you get your hand in it, instead of cutting off your fingers clean, it will likely pull in your whole hand and arm etc.... you get the point. Bottom line, sharpened is better, no matter who you talk too. That said, and the point is, the blades in the Alterna Jar are sharp, very sharp. For Blendtec applications, the blade in the jar has been sharpened on the right side, ... because the knives are rotating right ways - clockwise.
The drive socket gear is smaller in the Blendtec blenders, so of course the blade assembly in the Alterna jar for the Vita Mix blenders does fit into the Blendtec drive socket. Three things then; The Alterna blade assembly for the use in the Alterna jar on top of the Blendtec blender has a removable blade assembly that is sharpened, turns clockwise, and has the appropriate gear to fit on all Blendtec blenders, except with use in a sound enclosure. For that, there is a new jar on its way in the early 2016.
The blades therefore being different for the use in the Alterna Jar on top of the Waring 3.5 hp blenders and it's alike-kind-type blender bases. The knives are sharpened on the left side of the blade because it turns counter-clockwise. The gear is larger thicker because the drive socket part of that area of the blender motor axle is larger.
Then how do these different Alterna Jar configurations sit on each of these blenders? The Alterna Jar sits on the Blendtec blenders just normal, line its original Wildside or Fourside jar, straight and square. Remember, the Alterna jar was made with the intention that it also fits on the other kind blenders, like Waring, Omni, Vitamix,.... That in mind we engineered the bottom base of the jar in a way that just by turning the jar 45 degrees in an angle it would also fit on the other kind blender bases, thus missing the rubber cushion stubs.
People or restaurants that have both type of blenders, have the opportunity to switch the blade assembly out accordingly and use the Alterna Jar on both blenders. It is not so much that one should switch back and forth between the two uses. Mostly it is advantageous for restaurants that have Blendtec blenders in their shop and want to switch their blender equipment to Waring or Vitamix, for example. They don't have to buy all new jars. A Blade assembly is so much more inexpensive.
By Alterna Jar
Blenders from Vita-Mix come along with a tamper accelerator tool, whereas Blendtec and Waring do not offer it. Officially advertised, the blending cycles of Blendtec blenders exclude the need for a tamper accelerator tool, and Waring chooses not to avail one to customers. Certain consumers however find it necessary having a tamper present sometimes. Others prepare their smoothie, purees, nut butters, creams, and soups with intent of using a stirring tamper tool.
While Blendtec is stating as a marketing type method that no tamper is needed, in various cases it is more than handy to have one available because if you do get stuck with your food then it is safer to have one than for example using a fork or spatula to give the ingredients a quick push-down to get the blending motion going.
Different names are assigned to a tamper, relative to its manufacturer, whether from Blendtec, Waring or Vitamix in this case. A majority of individuals refer to it simply as a tamper. This important tool is used for pushing down ingredients to the upper proximity of the blade level, but with some safe distance, to achieve accelerated blending process of content such as raw soup, puree, nut butters, or smoothie. Utilizing an accelerator tool moves ingredients forcefully towards this blade, which rotates at extremely high speeds.
Vita-Mix Accelerator Tool is made from a polycarbonate type plastic comprising a lid hand which closes off the hole formed inside blender container lid while in use. The tool moves freely in and out of the container. Downward action of content creates vacuum action which sucks it into the container as blending takes place. Vita Mix recommends that one use their Accelerator tool throughout the process of blending to expedite the action. Their so-called patented accelerator tools to vacate air pockets are almost needed all the time as per Vita-Mix advertising. But air pockets according to a lawsuit between Vita-Mix and Basic and its follow up appeal confirmed that Vita-Mix however was unable to successfully proof air pockets. One could simply add more water to the ingredients and create the vortex action. But you don’t always want a more liquid concoction.
Certain retro-fitted tamper tools are available in the market. Some blender operators also prefer using a plastic tool or wooden dowel for pushing down towards the blade in rotation to accelerate blending operation. As a result the tamper gets blended up and/or damaged. This could be due to use of an appropriate Accelerator tool with lid in place. If one were not to use a tamper tool appropriately with lid in place, say, for example a fork or knife, or even a hand, pushing down on ingredients that way in high performance blenders could lead to very serious injuries, amputation, and/or damage to the blender units and blades.
Blending Soups and Purees with or without Tamper
When preparing ingredients for smoothies or soups, water is normally added. A tamper may not be necessary to use while blending the content, if sufficient liquid or water is added to the other raw ingredients. A hollow cave area appears just above the blade only when excessive amount of ice is applied for the smoothie process, with the blender cycle turning too fast. Blendtec blenders like the HP3A or Total Blenders are designed with the versatile blending programs it operates, which eliminate the necessity of using a tamper, supposedly. It is “supposedly” because this claim is not always true. There are just too many variables in blending that could be the amount of ingredients, how they are placed, which one first, what consistency they are, what the liquid to solids ratio is, if there are some obstructions like large ice section, and the timing of the blender, the blender motor strength and momentum of turning and starting up, etc. Still, one may require some type of tool to push down the blending ingredients, maybe for stirring, maybe just enough of a push to get the blending action going. Once it is running, meaning you see all the ingredients cycling, the blades will do all the rest of the blending by themselves.
Less amount of liquid is used when preparing a pate or puree in a high-performance blender. One may as well require some form of device for pushing down contents to the blade level. Blendtec especially makes its blenders to operate without needing an accelerator tool or tamper. However, consumers report using cutlery and other equipment to push down the ingredients.
Especially when making nut butters (i.e. Almond butter), a tamper tool is mandatory. The nuts are too heavy and oily, so they are sticky, they just will not freely circulate with the blade turning action. You need to help it to move along and turn over the massive almond puree until it gets oily and is ready for consumption.
The Universal Tamper Accelerator Tool made by Alterna is a great device which fits into any blender jar. Some exceptions exist, like for the Ninja, which lacks the blade construction appropriate for allowing tamper-insertion. The Ninja’s blade is really like an auger that does not let the user insert the tamper. The universality of the Alterna tamper means that it literally can be adjusted and set at different height levels from the area where the tamper is inserted into the jar through the hole in the lid. This adjustability is important to make sure that the tamper will never touch the turning blade during operation when inserted into the jar. Different blender styles and brands have different dimensions from the hole in the lid down to the tip of the blade.
Acetal Delrin, the material employed in making this tamper is approved by FDA “for food contact.” As a precautionary measure, the 2 pieces of flanges (rings) are clamped around the location desired, fitting the tamper in firm manner, the location being the adjustment area that determines the remaining length of the tamper end that is being inserted into the lid cap hole, reaching down towards the blades. This keeps the low tamper-end from touching the blades once inserted through the lid.
The Alterna tamper can fit into Vita-Mix 64 ounce containers, the 32 oz jar, Blendtec Wildside or Fourside, all the Waring and Hamilton Beach blenders, and Kitchenaid, Cusineart, Oster blenders. You name it, if the blender has a jar with a removable lid cap and a regular type blending blade cutting unit, the Universal Tamper come universally adjustable in as a very handy tool. It is apparently better to have it and not need the tamper, than needing it and then using a fork or worse, your hand.
Wood tamper dowels too are becoming quite popular to be used as tampers. They are relatively inexpensive and easy to make when one has a drill machine. Just cut the dowel to length between 8 to 12 inches, usually a dowel with a diameter of 1 inch. Drill in a hole of 3/8” where the appropriate location of the stoppage cross rod should go through to prevent the dowel from entering the jar through the opening in the lid. This cross dowel will prevent the dowel ‘hopefully’ from touching the blades during the blending action. Otherwise, if the wood dowel touches the blades, it will splinter severally making the dowel unusable for future blending actions. Wood also has the likely tendency to absorb water and is therefore very insanitary.
Some people like wood better over plastic, because if by accident one were to blend in untreated wood into ones smoothie, the smoothie would at least still be somewhat edible, subject to one’s appetite. Of course if plastic is blended into a smoothie, you would have to through it all away, for sure. The Acetal Delrin material does not splinter much and therefore unlike with the wood and the completely shattering hollow plastic tamper, Acetal Delrin (POM) is a solid compressed high density material that will be rendered reusable as a tamper stick. From that aspect, and because POM has been used for food processing in food contact for decades, it is an ideal material for the food blending applications as a tamper accelerator tool.
Using blenders from Waring, Vitamix and Blendtec delivers the same gain of blending raw foodstuffs into consumable products. However, each of these has unique features that distinguish their functionality. Alterna jars also introduce an innovative perspective into the blending process. It is necessary to evaluate the distinct characteristics of all the blending equipment above to enable users make the appropriate decision when performing blending operations. Below is an assessment of the various features of Waring MX1000 to MX1500XT high power blender series, Vitamix 5200/6300, and the Blendtec various blenders as well as the Designer Series Blenders.
Waring 3.5 Hp MX1200XT Series Blender
- Shatterproof and heavy-duty plastic material used for creating the lightweight and BPA-free carafe
- Powerful 3.5HP motor and strong stainless-steel blades crush ice, creating frozen cocktails and blending thick and creamy smoothies
- Warranty of two years from Waring
- The electronic keypad membrane is easy to clean with a beautiful blue backlit LCD screen.
- Adjustable speed control provides for variable speed function to allow different type of operations and at different speeds.
- Reprogrammable beverage stations for ease of use on some models.
- Dual pulse functions.
- Debatable 45,000 RPM bare motor speed for powerful and fast crushing operation.
- Price range (MX1000) starting below $300 and going over $700 (MX1500)
- Does not come with a tamper tool, but really could use one. The jar is squared off on bottom from wall to bottom of container area – there is no transition.
Vitamix 5200/6300
- Relatively costly at around $450 to $500, upwards to $600 and $700, depending on the model you buy, and offers basic blender setup, having standard pitcher of 64 ounces – smaller sized jars are available.
- Certified Reconditioned blenders available at lower cost but are not necessarily new.
- Free shipping provided within the US if blender is ordered through a link on most affiliate marketing sites with a coupon code.
- Features 2-peak horsepower motor which spins blade at variable speeds
- 7-year manufacturer’s warranty for residential use and 1 to 2 years for commercial use.
- Highly-versatile and durable blender
- Quite tall at 21 inches with pitcher
- Four-tipped blade that is separate from pitcher (Vitamix has wet, dry, and ice blade options)
- Toggle switch and dial interface offers precise, manual blending control
- Includes tamper tool for pushing down blending contents
Blendtec Designer Series Blender
- Fairly expensive ($500 / $600) with just the basic blender setup offered which comes with 64-ounce standard pitcher
- Factory Recertified blenders available only for Total Blender Classic Series
- Free shipping offered for US orders done via some online resellers
- More power with 3 peak horsepower motor of 1560 watts and high spin-rate (is a marketing driven term)
- Manufacturer’s warranty of up to 7 years available in the USA residential use, Commercial 1 to 2 years in the USA. Europe and Australia have less warranty
- Durable and highly versatile functions
- Relatively short at 15 ½ inches with pitcher and can thus fit under regular kitchen cabinets
- Blade fused to pitcher making it necessary to replace blade alongside pitcher
- Features ‘touch user interface’ and not buttons for control functions
- Lacks tamper but has square-pitcher and special straight-blade design for efficient blending
- Straight, single-prong, wing-tip blade
- No tamper claimed to be necessary. But consumers have repeatedly requested tamper availability – See Universal Tamper.
Advantages of Alterna Jars
- Offers good retrofit on multiple blending machines of high-performance, including those from Vitamix, Blendtec blenders, Waring and JTC Omniblend, few among others
- Sits straight onto Blendtec, and on Vitamix, Omni, Waring 3.5HP and Good4U blenders in angel perpendicular 45 degrees turned
- Gears modified in various dimensions for correct fitting into applicable blenders
- Capable of producing diverse concoctions and blends like smoothies, ice cream, hot soups, sauces, sorbet, purees, rice, paste and broccoli and ice cubes among others. Improves blending quality especially with nut butters, strawberries, raspberries, blackberries, and other real hard to emulsify ingredients that would otherwise leave visible particles
- Features replaceable blades compatible with Blendtec, Vita-Mix, Omni and Waring blenders
Selecting the correct blade-cutting assembly unit enables users of Alterna jar to achieve convenient blending operations with their blender.
By Alterna Jar (C) 2015
The Alterna Jars are engineered and developed in the USA with the intention to retrofit one and the same container perfectly
on multiple high performance smoothie blending machines. These are all Blendtec blenders, Vitamix(TM), JTC Omniblend, Waring(TM) MX1050XT blenders, and a few others. Blendtec blenders have a different jar base design and normally a Blendtec(R) jar will not fit onto the Vitamix or Omni Blender or Waring blenders (MX Raptor type). And the Vitamix blender jars, Waring, Omni JTC fit all on the other blender base, but they do not fit on the Blendtec blender base, normally.
And so we have designed a container that fits on both of these general blender platforms. The only difference is, you will sit the Alterna jar onto the Blendtec blenders straight, and on Waring, Good4U, etc... blenders in an angel perpendicular 45 degrees turned. The patent-pending design with specifically engineered jar cutouts allow space for the Alterna jar to sit on the Waring rubber blender cushion (and JTC and Vitamix...). The Waring et al blenders turn counter-clockwise and Blendtec turns clockwise, however. And so the blades need to be sharpened on opposite sides and the user who wants to use the Alterna Jar on a Blendtec blender must have the correct Alterna Blade for Blendtec blenders installed while the user who wants to use the Alterna Jar on a Vitamix or Waring or JTC blender, must use the jar with the correct Alterna blade blending assembly for the Waring and JTC et al blenders. The gears are modified in size and dimensions accordingly to fit correctly into the applicable blender.
Note, minimum size of blending capability is 16 ounces and maximum effectiveness is at around 55 ounces to 64 ounces, depending on liquid content ratio to solids. The Alterna Jar is capable of various blends and concoctions such as smoothies, hot soups, ice cream, sorbet, sauces, purees, paste, rice, grain to flour, broccoli, cabbage, avocado pits, ice cubes...
The other patent-pending engineering of this high performance jar set up for perfect Blendtec blender and Waring (et al) blender application is the requirement to elongate the gear - shaft to make room below the jar (jar and gear patent pending) for the bottom plate screw / nut so you can tighten down the changeable replaceable blade unit cutting blending assembly on the Alterna Jar specifically for Blendtec blender applications. Blendtec does not have jars with replaceable blades, but Vitamix and OMNI and Waring however do.
We have noticed on many occasions that customers / blender users would have bought a Blendtec blender but instead bought a Vitamix or JTC Omni blender or Waring MX1050XT blender because Blendtec has a fixed installed blade. The issue is, the blade will wear out (the bearing / bushing, to be exact) and then the blender operator has to purchase a brand new Blendtec jar. Bearing-operated blade assembly cutting units hold up longer than bushing driven blades, because they have better seals and gaskets and harder bearings (bearings are better than bushings). The bearings balls are made from a carbide alloy, the same used for roller skates and blades. And this is a big money savings issue especially for restaurant smoothie shop operators.
No matter if you have a Vitamix, Waring MX XT blender, JTC Omni or Blendtec blender, you can use the same Alterna Jar, however by selecting the correct blade cutting blending assembly unit. Select between the Alterna Blade - Blendtec or Alterna Blade Waring, Waring also fitting on Vitamix, Good4U Raw Power, and JTC Omni Blenders, perhaps others, such as Omega and Centaur blenders.
Disclaimer: We are no longer selling smoothie blenders. The mere fact that our Alterna Jar and it's blades are interchangeable and also fit on various other diverse high power blender brands is not prohibited by law, but not likely supported by it's brand owners. Brand owners may probably do and/or threaten to void warranty, however Alterna will gladly issue warranty coverage over said claimed equipment if it can legitimately be proven that a problem may have been caused by the Altern jar and/or its blade mechanism and its usage, provided it has been used correctly in accordance to our jar and blade maintenance guideline. If a blade has seized up and being used regardless, it can cause potentially to drive socket and/or cause motor damage. The trademarks of Waring, Vitamix, Blendtec, etc... are owned by their applicable owners. The Alterna Jar and Blades are patent pending and trademark registered.
It's an Alterna Blender Jar LLC Company. We provide innovative newly developed Jars, Blades, Tampers, and after-market replacement parts and components for the most popular high performance blender brands (patent pending). These are Blendtec, Waring, Good4U, JTC Omniblend, to name a few most popular ones, among others. Our Alterna Jar, as the name already says, is the best replacement alternative for Blendtec blender containers, which features our patent pending US engineered and assembled exchangeable interchangeable and replaceable blade assembly blending cutting unit. Our Alterna Cutting Units are made from the highest grade materials and seals to provide longevity and versatile blending options from wet, dry, ice, grain, powder, drink, juice, smoothie, shake, puree, sauce, butters, hot soup, and ice cream textures; all-in-one blade assembly as well as specialty knives.
Blender operators can use the same Alterna Jar that fits on Blendtec blenders also on their Vitamix, JTC OmniBlend, 
Waring MX1050XT blenders (and all other Waring MX1000XT, MX1100XT, MX1200XT, MX1300XT, MX1500XT and Good4U Raw Power Commercial 3.5 HP blenders), by switching out the blade cutting unit (because they turn in opposite direction and the gear size is different). The same jar, although the various blenders are designed with different size blender bases for their proprietary jars, just needs to be turned by 45 degrees to sit perfectly onto the various high performance blender base (patent pending filed).
This is the best website where you will find versatility and make-sense after-market retrofit inventions for consumer and smoothie business operators. We offer low prices for our quality products and give our consumers and authorized global resellers the opportunity to add value to their equipment and their pocket book.
http://www.alternajar.com
From a consumer standpoint, a refurbished high performance blender, such as the Blendtec blender series, and other competitors in the $500 price club, appears at first to be a nice deal. There are however several points of views to look at as to why companies could have refurbished blenders in stock, why they are offering them, and who would return them - in what quantity - and why?
To the most part, these factories over-sell and under-deliver unfortunately to the dissatisfaction of the many customers who return their expensive blenders to the factory directly or through the retailer. The factory then goes over the blender and cleans it up and puts a new unused jar with a new recipe book into a new box and then offers the blender for sale as refurbished. This is one most plausible theory.
Why would a customer not be happy or satisfied with an expensive high performance blending machine? This is one possibility that has been found at Costco and at Sams Club. The consumer sees and tastes a fine magical smoothie during a demo show. The blender demonstrator, well experienced and highly trained, shows off fancy tricks and concoctions that leave the consumer at a jaw-dropping awe. Once at home with the new shiny toy, duplicating the smoothie is some other foreign story and the remorse sets in. And the cycle of return begins.
What is wrong with that picture? Yep. We like to educate our customers about gimmick purchases. No, a blender does not heat soup with an electric heating element (it heats soup with the blade unit that turns into a heating element because of friction). No you don't need a dedicated button to crush ice, make peanut butter or almond butter. A yes, you are paying at $ 400 to $500 already way too much for a 3 horsepower high performance blender when you can get the same thing in brand new for half the price. Look at the OMNI Blender for example. Half the price?
Still be aware of the many crappy not so well built and under-performing blending machines. Some totally copy the Vitamix, Blendtec blenders, and the OMNI blender straight out. Ninja, Nutri Bullet, the Health Master, all are inferior to the big and powerful blenders, the name of the game. We have sold many different blenders and have gone away from it and now are just focusing on the OMNI Blender. The JTC OMNIBLEND blender is the best blender bang for the buck because of its quality, power, warranty, and low competitive price.
We have been in business selling blenders since 2007. Ever since, having carried many different high quality high powered blending machines, we have wondered why we can't sell refurbished blenders? The simple answer is: Hardly ever anyone returns the blender. Why do you think that is? We leave it by that because that fact and question is already a good enough answer in itself. And why do you want a refurbished blender when you can get a brand new OMNI Blender for the same price as other used ones? Do you want the chance to have someone else' hair in your smoothie?
If we had refurbished blenders available, they would cost $225 including shipping and would be cleaned up, coming with a new jar and blade, tamper, and new recipe book, all in a new box and full 7 year standard warranty; that is if enough customers would return theirs. But they don't. Customers have the opportunity to purchase the OMNI 3 hp smoothie blender and review it for 30 days and take advantage of our return policy should they wish to return it within that time frame.
I order to reduce the likelihood of a consumer to return a blender we focus on education of our blender, what it does, how it performs, and how to make smoothies, in the front-end before they are buying their high powered blender. A refurbished blender could theoretically also be returned, it just has never happened.
(C) 2014 OmniBlender.COM LLC
And so we have designed a container that fits on both of these general blender platforms. The only difference is, you will sit the Alterna jar onto the Blendtec blenders straight, and on Waring, Good4U, etc... blenders in an angel perpendicular 45 degrees turned. The patent-pending design with specifically engineered jar cutouts allow space for the Alterna jar to sit on the Waring rubber blender cushion (and JTC and Vitamix...). The Waring et al blenders turn counter-clockwise and Blendtec turns clockwise, however. And so the blades need to be sharpened on opposite sides and the user who wants to use the Alterna Jar on a Blendtec blender must have the correct Alterna Blade for Blendtec blenders installed while the user who wants to use the Alterna Jar on a Vitamix or Waring or JTC blender, must use the jar with the correct Alterna blade blending assembly for the Waring and JTC et al blenders. The gears are modified in size and dimensions accordingly to fit correctly into the applicable blender.
Waring MX1050XT blenders (and all other Waring MX1000XT, MX1100XT, MX1200XT, MX1300XT, MX1500XT and Good4U Raw Power Commercial 3.5 HP blenders), by switching out the blade cutting unit (because they turn in opposite direction and the gear size is different). The same jar, although the various blenders are designed with different size blender bases for their proprietary jars, just needs to be turned by 45 degrees to sit perfectly onto the various high performance blender base (patent pending filed).