Pros and Cons of Aftermarket Replacement Blender Containers October 26 2015

Aftermarket components and products are produced and sold to consumers in various different markets. It is very common in the consumer technology industry as well as in the automotive industry. Aftermarket products and components / replacement parts usually are an indicator that a certain product is very popular. It is also associated to money savings to the consumer. In the pharmaceutics industry, the term ‘generic’ is often used. Perhaps the latter is not really an aftermarket component in the sense this article is referring to.

Blendtec®, Waring™ MX series of blenders, as well as Vita Mix® blenders are just three blenders from among a few other high performance smoothie blenders, of which a whole ton of are presently in use globally. It is estimated some 100 million of these particular powerful blenders roam the Earth in peoples’ kitchens and restaurants. About 60% of them, according to a study, are not in use. Why they are not in use is not really known. It could be in part a reluctance of user-interest and/or that and being broken down and just never having gotten to it to make a ‘replacement’ attempt of a broken blender blade or jar.

Most people are not very technically inclined. When their jar breaks, or the blade bearing of blade assembly in the jar seizes up, they interpret it as a broken down blender. The blender gets put aside until time and effort is made to make the warranty call, or if the warranty is expired, a new jar is purchased. If the blender is misdiagnosed as dead and broken, not being sure what is bad, time may tell that these high percentage consumers have their ‘broken down’ blender collect dust in storage.

In the case of these blenders, aftermarket components, such as replacement blade assembly cutting units (the knife, or in other words the blades) will be a money saver and a convenient solution, if only the consumer in possession of the broken down Blendtec or Vitamix blender (or Waring and others – non one brand in particular) would dig into finding out more about alternative replacement parts.

It is however not just about replacing a broken part, in the aftermarket industry. Additional jars offer opportunities to have spare parts for just in case, and an additional container for the purpose of alternating blender jars. The Kosher blending enthusiasts of course always use 2 jars. There are certain advantages to the number 2, two jars in possession rather than just one, especially when they are different. Blending is often better in one jar than in another depending on what one blends up.

The Alterna™ Jar, the aftermarket jar reported on in this article, brings several advantages to the table. Current users have reported an increase in finer blending, smoother concoctions, more thorough emulsification. The actual blending capacity is 80 ounces of ingredients. The jar is also, like the OEM factory containers, a BPA-Free copolyester material, with stainless steel removable blade assembly, and tamper stick accelerator tool available.

The advantages are certainly not always enticing to everyone, for example money savings. Some people may find a Blendtec Fourside replacement container for $60 plus shipping. Why would one purchase an aftermarket non-factory container for $80 including shipping? Those that do, are not buying it for immediate savings, or not for money savings reasons at all. The reason for that is that the old type Blendtec jar is always the same, no improvement with a blade that is just going to break again eventually and a new complete whole jar has to bought again, even if the price is only $60 instead of $80. If that same scenario happens with the Alterna Jar, one would have to simply just purchase a replacement jar for $35, instead of $60 for a new jar by Blendtec. Of course, Alterna has a package deal available for real blender enthusiasts, which is the jar with a blade already installed, plus an extra replacement blade for $99, including shipping.

Let’s assume the Alterna blade goes out at the same time the Blendtec blade would seize up, in the Blendtec jar. At that point the OEM factory enthusiast would have spent $120 while the aftermarket consumer fan spent only $99. But, again, not everybody may be interested in the cost factor issue. The Alterna jar blends better, blends bigger volumes, and is a heavier duty jar overall.

Waring MX series blenders, those that are truly 3.5 horsepower monsters, come with rather inferior blade and jar design. The OEM Waring container has a poor warranty, to one hand. On the other hand, the vertical jar wall goes into the bottom of the jar without curvature straight in a straight 90 degrees. There are numerous reports of poor performance and warranty issues and poor customer service. Plus a 2 Liter replacement jar from Waring costs anywhere from $120 to $160. The Alterna aftermarket container configured for the Waring MX series blenders performs better, hold up better and costs less as well.

Vitamix… ditto to Waring.

In conclusion, aftermarket is not for everyone. OEM has its advantages especially when the blender is still under warranty. In Europe or in Asia, Australia and South America, Blendtec and Vitamix warranties are general between 2 to 4 years maximum. Waring already has a 2 in 1 year warranty in the USA which means 2 year parts and 1 year labor. Costs of replacement jars in non-USA markets are mostly prohibitively expensive. In Brazil a Blendtec Fourside jar is $150 USD and $200 has to be coughed up for a Wildside jar. The same in Europe, the UK, in Australia and all over the Asian Rim.

Those consumers that consider the advantage of aftermarket recognize that aftermarket means that the OEM brands are going to stick around more likely longer, aftermarket components will bring the prices down everywhere, and aftermarket blender containers offer a convenience, a choice, a versatility, especially when this one blender jar actually fits on all, Vitamix, Waring, JTC Omni, Klarstein, Optimum, Omega blenders, and the Blendtec blenders.

Note, how the Alterna Jar sits on the various blenders, straight on Blendtec, and diagonally by 45 degrees on Vita Mix, Waring, and JTC Omni blenders. This is a little different than with any other blender jars, but it works, and is actually mostly designed that way so the same container can be used namely on different blender bases, such as the Blendtec and the Waring kinds.

Pros and Cons, if a blender were still under warranty, and consumer wanted to use the aftermarket Alterna jar, it is most likely assumed that the given factory might tell the consumer that such application is not authorized and will likely void the warranty. If the Blender motor might break, such use opens up the question of whether the jar and the aftermarket blade bearing may have contributed to, or perhaps was the cause of premature motor failure. However, there are several issues to that.

If the blade seizes up on any blender jar, it is the consumer's responsibility to stop using it, replacing the whole jar or the blade assembly from the Alterna jar with removable replaceable blade assembly unit. Plus, who is to say that a given consumer has not already over exerted their blender motor when running the blender motor with a seized up blade unit in their jar for far too long of a time and have not noticed it. Sure, if it can be proven that there is a relationship between the Alterna jar aftermarket container and a broken motor, it would only be fair that warranty is assumed, if there is a warranty. However, in every possible scenario, it should be taken into account, that it just cannot be proven. There are too many variables from abuse to a defect from the blender factory to begin with or simply just heavy normal use and therefore wear and tear having lead to an early natural death of said blender motor. It is simple, anyway, it should be considered to always pay close attention to the condition of the blade assembly and bearing, no matter if the user operates an OEM factory brand blender container or an aftermarket blender jar.

In any case, OEM brand factories should be exited about aftermarket blender jar availability. It is a sign that the market has reached a certain saturation and the brand is here to stay. The consumer views more choices and availability as convenient and as a great advantage, actually and eventually bringing down prices and helping to improve quality.

Copyright 2015 (C) Alternajar.com LLC

Comparisons of Blender Jars with a Fixed Installed Blade to one with a Removable Blade Assembly August 12 2015

Blenders for the delicious smoothie concoction production are employed in restaurants, smoothie shops, or at home among many people in the world. These blenders come with different features, different sizes of containers, their blades / motors turning in either direction, sharp or dull blades / knives and various different designs of blade knife shapes. The issue discussed here is however the pros and cons of blenders and their jars with a removable or a fixed installed blade assembly.

A removable blade assembly is a blade cutting unit containing the knives connected to a shaft that connects to the blender gear. In between is a bearing that keeps the assembly turning smoothly without interruption. These bearings are a conglomerate of steel, usually carbide steel balls sealed up like also seen and used in roller blades. This sealed bearing unit is inside a housing along the shaft that is sealed from both ends in and outside of the jar to prevent water from leaking through either direction.

The blade assembly is inserted into the jar from the inside, sitting it into a hole on the bottom of the blender container. The blade assembly has a threaded area on the bottom. As inserted, from the outside a so-called nut or blade bottom plate, also known as a blade retaining nut (depending on who is the manufacturer), is then screwed onto the thread. This tightens and seals the blade assembly inside the jar to the container bottom and on the outside bottom. In between the bottom plate and the jar is a O-Ring gasket inserted that prevents water from entering.

Various styles of blades knives exist. Most companies use a 4 part or even a 6 part knife assembly where 4 to 6 knives protrude from the center shaft on top of the blender cutting assembly into different directions. Some of these ends point upwards 45 degrees, some are about horizontal, and others point down.

The blending results vary depending on the blade design together in connection with the layout and design of the blender container subject to specific interaction. The best type of blades are sharpened knives, sharp is better than dull.

These type of blades are usually made for jars that sit on blender motors which turn counter-clockwise. This is really for no scientific particular reason. At least some few smoothie and raw food gurus might claim there could be a cosmic harmony at play if the blender motor and the knife cutting assembly turn with the earth rotation, which is counter-clockwise. This may however at the minimum be really far-fetched from a credible reality.

Blender brands such as Vita-Mix, Waring, Hamilton Beach, JTC Omniblend, Omega, Kitchenaid, along that line, a few among many other blenders, have motors that turn counter-clockwise. In general, and usually, the more expensive upper-blender class has jars with very sturdy durable blade units that are screwed on from the outside of the blender container. The cheaper low-end blenders like Kitchenaid, Oster, Cusineart, and low end Hamilton Beach have much thinner units and also have to come off every time a jar needs washing.

Washing a jar with the blade installed or taken out should always be an option. Taking the blade out may also have the associated benefit to replace if the bearing might be worn out or simply has seized up due to age and wear and tear. It is just more sanitary if a user has the option and discretion to remove the whole blade assembly unit for cleaning, or for replacement if broken, or for sharpening or re-sharpening… any kind of maintenance.

Usually those companies that offer blender jars with removable or replaceable blade assembly cutting units, also offer a jar without blades by itself and the blade assembly by itself.

The bearings of these type of blades are prong usually to seize when over-exposed to water either through washing them in the dishwasher or soaking the jar and the blades inside the sink. It is possible that water could get into the bearing housing, although not likely or it won’t happen easily. It will happen over time due to wear and tear, and then the blade needs to be replaced, one of the advantages a removable blade – type blender container has over a container with a fixed installed blade, because that too tends to seize up.

As far as it is known, only Blendtec® offers a blender jar type with a fixed permanently installed blade. Instead of however equipped with ball bearings, these assemblies consist of bushings. A bushing is as opposed to balls (bearings) depending on a specific design, a buffer, a cushion type of two ends that are greased up and rub against each other in a manner that little friction arises, as little as possible.

In the cases of the Blendtec Jars, either Wildside®, the Fourside®, or the Twister® Jar, Blendtec uses such a bushing instead of ball bearings. This allows for a much smaller housing around the shaft that must stay lubricated to easily turn and follow the torque forced onto the dual wing-tipped blade assembly. By the way, Blendtec blades are not sharp.

The advantage of a bushing is that is uses up less space than the ball bearings in a housing and therefore can be installed closer to the motor gear, of course in respect to other blenders, that being really minimal. The disadvantage is that bushings are usually not as strong and durable as ball bearings.

Water still can get into the though hermetically sealed off blade shaft bushing housing, especially and controversially associated to the lack of usage. Water and usage usually keeps and helps to keep the bushing seal area lubricated and seal. If it dries out too long especially after usage it can often happen that the seal separates and the bushing seizes up and you can’t no longer use the container .

These types of bushing-operated blender blades are not replaceable. Sure they are removable and replaceable if one had the tools to remove them and put them back in once cleaned up and repaired. Consumers, especially however restaurant shop and smoothie shop operators tend to move away from fixed blade blender jars because of the cost factor. They have to replace the whole jar, which is still good and usable, however just because removable blade features are not available.

Other advantages of have a blender jar with the option to remove and replace blades is not just for the purpose of repair and maintenance, but also for opening the door to use and facilitate different styles of blades. Of course a controversy exists that one blade may do it all. But it has been proven, although in general it is true that even a dry blade can blend up wet ingredients, a wet blade also blends very effectively dry grain wheat ingredients and coffee, and ice too can be blended with any of the various blade and knife design setups, that differences and high efficiency outcomes vary subject to blade design. A smoothie shop that makes one kind of an ice type smoothie may over time help to save energy and even prolong the life of the jar and the blades all together as opposed to using a more generic blade assembly unit.

As introduced up on top, blending is done with much variable consideration to the design of the jar, the blades, and the sharpness, as well as the power of the motor, and believe it or not, also of how the ingredients are placed inside a jar, in which order, if hard solid frozen or fresh soft is on top or bottom. Even the use of a tamper adds to the variable of blending effectiveness.

Tampers are mostly only used when the consistency of the ingredients is more solid than liquid – it’s a liquid to solids ratio issue in most cases. As long as the blender unit can turn and create a vortex, the action in which the blades propel all ingredients in a turning action and creating a liquefying emulsifying texture of the ingredients, no tamper is needed. Getting stuck, especially when making intentionally solids purees or paste, even nut butters, some kind of a stir stick, aka plunger (ouch – not toilet related) can just give the push to get that vortex going or to stir the puree into a fine creamy concoction.

Sharper blades can cut better. That is definitely demystified. No way that dull knifes are better than sharp knives. The consumer and commercial smoothie market will soon see the Blendtec blender industry with sharpened knives. As a matter of fact, a company called Alterna jars already has come out with sharpened knives, they are also removable and replaceable, of course. The Alterna jar is made to fit on the Blendtec blenders, as well as with a simple blade assembly switch, will fit also on those blenders that turn counter-clockwise.

Elements of Warranty for Alterna™ Jar Blender Products August 12 2015

Elements of Warranty for Alterna™ Jar Blender Products

An extended warranty is at times known as service contract, service agreement or maintenance agreement. It refers to prolonged warranty availed to consumers, apart from the standard warranty covering new items. This form of warranty could be provided by the retailer, warranty administrator or manufacturer. Alterna offers a 1 year extended warranty for extra payment on top of its regular standard limited warranty.

A product deteriorates naturally with usage and this fact is not measurable in entirety due to the many variables it involves. Generally, a factory because of the feedback it receives and the product is sees, gets a good idea about wear and tear and what may be coverable under warranty. Inappropriate cleaning, storage or application arising from negligent action could for instance lead to excessive wear and tear. Product warranty does not apply in such cases. Alterna™ Blender Jar LLC extends warranty for its different products against defects under its limited warranty coverage, regardless of whether the product has been used or not.

The customer has to return the product for a claim to be valid, along with prepaying postage of stated warranty return. Warranty is subject to return authorization being provided via email or phone. The company reserves its right of authorizing other ways of demonstrating warranty coverage, such as through videos, email or even pictures. The warranty offered on Alterna Jar for instance, implies that the company can either replace or repair the product at their discretion as seems reasonable at its discretion. The key word is “REASONABLE”, reasonable to both, the company and the customer.

It is important not to use the jar if the blade bearings are either already or in process of seizing up. Performing manual checking and turning of blades back and forth from outside using the gear on regular basis can help in detecting such incidence. Leaks at the bottom outside of blade assembly or rough feel when turning blade are also indicative of the bearings wearing out, which normally happens prematurely in cases of the jar and blades having been washed in the dishwasher, soaked in the sink, or abused in some other forms. Such situations would warrant replacement upon verification by the manufacturer, however, with limitations. The following warranty conditions apply to Alterna products:

• Alterna Blender Jar LLC offers warranty of 1 year against defects on both jar and blade unit installed originally in the Alterna jar. This warranty is limited to only the first combination of jar and blade purchased and 1 year warranty is offered to a consumer who buys a complete jar with its blade.
• Warranty of 6 months is provided by Alterna Blender Jar LLC covering against factory material or assembly defects for replacement blades. The warranty of replacement blades bought directly from the company for a blade replaced from jar with expired warranty is 6 months.
• Customers can purchase an extended warranty of 1 year PLUS for complete purchase of Alterna Jar at the time of purchase. Such extended warranty lasts for 1 year, which thus adds a 2^nd year to the initial warranty of 1 year. The same limitations apply as well.
• Flange rings of the Universal Tamper carry warranty of 90 days against breakage within the region where the two flange rings of identical nature clip and snap together. The rod or dowel is itself not under warranty as it only breaks if blended up, which results due to acts of misuse or negligence. It is either because the flange assembly is placed on the rod at the incorrect location (too long – reaches the blades), the tamper is used without the lid in place, or the user pushed down too hard thus bending and flexing the lid excessively and the tamper therefore touches the blade and gets damaged. Customers should notify Alterna Blender Jar LLC within 30 days following its purchase, if flange pieces fail to install owing to sections being wrongly milled.
• Alterna Blender Jar LLC will also replace the motor unit of a competitor blender such as Vita Mix, Waring and Blendtec under certain circumstances. This is if the buyer can prove the Alterna Jar along with its blade despite proper usage, directly caused damage to such motor unit. This part of the warranty is challenging to prove because normally blender motors only break due to a problem in the blender motor itself and not because of the blade. A motor gets worn out due to what is blended inside the jar, and if the user blends with a blade assembly that seizes up. Old age, and normal wear and tear is certainly not covered.

Disclaimer: This article is not the official Alterna Blender Jar warranty. Please see www.alternajar.com for specific warranty details.

Considering the Importance of a Blender Tamper August 05 2015

Blenders from Vita-Mix come along with a tamper accelerator tool, whereas Blendtec and Waring do not offer it. Officially advertised, the blending cycles of Blendtec blenders exclude the need for a tamper accelerator tool, and Waring chooses not to avail one to customers. Certain consumers however find it necessary having a tamper present sometimes. Others prepare their smoothie, purees, nut butters, creams, and soups with intent of using a stirring tamper tool.

While Blendtec is stating as a marketing type method that no tamper is needed, in various cases it is more than handy to have one available because if you do get stuck with your food then it is safer to have one than for example using a fork or spatula to give the ingredients a quick push-down to get the blending motion going.

Different names are assigned to a tamper, relative to its manufacturer, whether from Blendtec, Waring or Vitamix in this case. A majority of individuals refer to it simply as a tamper. This important tool is used for pushing down ingredients to the upper proximity of the blade level, but with some safe distance, to achieve accelerated blending process of content such as raw soup, puree, nut butters, or smoothie. Utilizing an accelerator tool moves ingredients forcefully towards this blade, which rotates at extremely high speeds.

Vita-Mix Accelerator Tool is made from a polycarbonate type plastic comprising a lid hand which closes off the hole formed inside blender container lid while in use. The tool moves freely in and out of the container. Downward action of content creates vacuum action which sucks it into the container as blending takes place. Vita Mix recommends that one use their Accelerator tool throughout the process of blending to expedite the action. Their so-called patented accelerator tools to vacate air pockets are almost needed all the time as per Vita-Mix advertising. But air pockets according to a lawsuit between Vita-Mix and Basic and its follow up appeal confirmed that Vita-Mix however was unable to successfully proof air pockets. One could simply add more water to the ingredients and create the vortex action. But you don’t always want a more liquid concoction.

Certain retro-fitted tamper tools are available in the market. Some blender operators also prefer using a plastic tool or wooden dowel for pushing down towards the blade in rotation to accelerate blending operation. As a result the tamper gets blended up and/or damaged. This could be due to use of an appropriate Accelerator tool with lid in place. If one were not to use a tamper tool appropriately with lid in place, say, for example a fork or knife, or even a hand, pushing down on ingredients that way in high performance blenders could lead to very serious injuries, amputation, and/or damage to the blender units and blades.

Blending Soups and Purees with or without Tamper

When preparing ingredients for smoothies or soups, water is normally added. A tamper may not be necessary to use while blending the content, if sufficient liquid or water is added to the other raw ingredients. A hollow cave area appears just above the blade only when excessive amount of ice is applied for the smoothie process, with the blender cycle turning too fast. Blendtec blenders like the HP3A or Total Blenders are designed with the versatile blending programs it operates, which eliminate the necessity of using a tamper, supposedly. It is “supposedly” because this claim is not always true. There are just too many variables in blending that could be the amount of ingredients, how they are placed, which one first, what consistency they are, what the liquid to solids ratio is, if there are some obstructions like large ice section, and the timing of the blender, the blender motor strength and momentum of turning and starting up, etc. Still, one may require some type of tool to push down the blending ingredients, maybe for stirring, maybe just enough of a push to get the blending action going. Once it is running, meaning you see all the ingredients cycling, the blades will do all the rest of the blending by themselves.

Less amount of liquid is used when preparing a pate or puree in a high-performance blender. One may as well require some form of device for pushing down contents to the blade level. Blendtec especially makes its blenders to operate without needing an accelerator tool or tamper. However, consumers report using cutlery and other equipment to push down the ingredients.

Especially when making nut butters (i.e. Almond butter), a tamper tool is mandatory. The nuts are too heavy and oily, so they are sticky, they just will not freely circulate with the blade turning action. You need to help it to move along and turn over the massive almond puree until it gets oily and is ready for consumption.

The Universal Tamper Accelerator Tool made by Alterna is a great device which fits into any blender jar. Some exceptions exist, like for the Ninja, which lacks the blade construction appropriate for allowing tamper-insertion. The Ninja’s blade is really like an auger that does not let the user insert the tamper. The universality of the Alterna tamper means that it literally can be adjusted and set at different height levels from the area where the tamper is inserted into the jar through the hole in the lid. This adjustability is important to make sure that the tamper will never touch the turning blade during operation when inserted into the jar. Different blender styles and brands have different dimensions from the hole in the lid down to the tip of the blade.

Acetal Delrin, the material employed in making this tamper is approved by FDA “for food contact.” As a precautionary measure, the 2 pieces of flanges (rings) are clamped around the location desired, fitting the tamper in firm manner, the location being the adjustment area that determines the remaining length of the tamper end that is being inserted into the lid cap hole, reaching down towards the blades. This keeps the low tamper-end from touching the blades once inserted through the lid.

The Alterna tamper can fit into Vita-Mix 64 ounce containers, the 32 oz jar, Blendtec Wildside or Fourside, all the Waring and Hamilton Beach blenders, and Kitchenaid, Cusineart, Oster blenders. You name it, if the blender has a jar with a removable lid cap and a regular type blending blade cutting unit, the Universal Tamper come universally adjustable in as a very handy tool. It is apparently better to have it and not need the tamper, than needing it and then using a fork or worse, your hand.

Wood tamper dowels too are becoming quite popular to be used as tampers. They are relatively inexpensive and easy to make when one has a drill machine. Just cut the dowel to length between 8 to 12 inches, usually a dowel with a diameter of 1 inch. Drill in a hole of 3/8” where the appropriate location of the stoppage cross rod should go through to prevent the dowel from entering the jar through the opening in the lid. This cross dowel will prevent the dowel ‘hopefully’ from touching the blades during the blending action. Otherwise, if the wood dowel touches the blades, it will splinter severally making the dowel unusable for future blending actions. Wood also has the likely tendency to absorb water and is therefore very insanitary.

Some people like wood better over plastic, because if by accident one were to blend in untreated wood into ones smoothie, the smoothie would at least still be somewhat edible, subject to one’s appetite. Of course if plastic is blended into a smoothie, you would have to through it all away, for sure. The Acetal Delrin material does not splinter much and therefore unlike with the wood and the completely shattering hollow plastic tamper, Acetal Delrin (POM) is a solid compressed high density material that will be rendered reusable as a tamper stick. From that aspect, and because POM has been used for food processing in food contact for decades, it is an ideal material for the food blending applications as a tamper accelerator tool.

Assessing the Strategic Benefits of Different Blenders August 04 2015

Using blenders from Waring, Vitamix and Blendtec delivers the same gain of blending raw foodstuffs into consumable products. However, each of these has unique features that distinguish their functionality. Alterna jars also introduce an innovative perspective into the blending process. It is necessary to evaluate the distinct characteristics of all the blending equipment above to enable users make the appropriate decision when performing blending operations. Below is an assessment of the various features of Waring MX1000 to MX1500XT high power blender series, Vitamix 5200/6300, and the Blendtec various blenders as well as the Designer Series Blenders.

Waring 3.5 Hp MX1200XT Series Blender

• Shatterproof and heavy-duty plastic material used for creating the lightweight and BPA-free carafe
• Powerful 3.5HP motor and strong stainless-steel blades crush ice, creating frozen cocktails and blending thick and creamy smoothies
• Warranty of two years from Waring
• The electronic keypad membrane is easy to clean with a beautiful blue backlit LCD screen.
• Adjustable speed control provides for variable speed function to allow different type of operations and at different speeds.
• Reprogrammable beverage stations for ease of use on some models.
• Dual pulse functions.
• Debatable 45,000 RPM bare motor speed for powerful and fast crushing operation.
• Price range (MX1000) starting below $300 and going over $700 (MX1500)
• Does not come with a tamper tool, but really could use one. The jar is squared off on bottom from wall to bottom of container area – there is no transition.

Vitamix 5200/6300

• Relatively costly at around $450 to $500, upwards to $600 and $700, depending on the model you buy, and offers basic blender setup, having standard pitcher of 64 ounces – smaller sized jars are available.
• Certified Reconditioned blenders available at lower cost but are not necessarily new.
• Free shipping provided within the US if blender is ordered through a link on most affiliate marketing sites with a coupon code.
• Features 2-peak horsepower motor which spins blade at variable speeds
• 7-year manufacturer’s warranty for residential use and 1 to 2 years for commercial use.
• Highly-versatile and durable blender
• Quite tall at 21 inches with pitcher
• Four-tipped blade that is separate from pitcher (Vitamix has wet, dry, and ice blade options)
• Toggle switch and dial interface offers precise, manual blending control
• Includes tamper tool for pushing down blending contents

Blendtec Designer Series Blender

• Fairly expensive ($500 / $600) with just the basic blender setup offered which comes with 64-ounce standard pitcher
• Factory Recertified blenders available only for Total Blender Classic Series
• Free shipping offered for US orders done via some online resellers
• More power with 3 peak horsepower motor of 1560 watts and high spin-rate (is a marketing driven term)
• Manufacturer’s warranty of up to 7 years available in the USA residential use, Commercial 1 to 2 years in the USA. Europe and Australia have less warranty
• Durable and highly versatile functions
• Relatively short at 15 ½ inches with pitcher and can thus fit under regular kitchen cabinets
• Blade fused to pitcher making it necessary to replace blade alongside pitcher
• Features ‘touch user interface’ and not buttons for control functions
• Lacks tamper but has square-pitcher and special straight-blade design for efficient blending
• Straight, single-prong, wing-tip blade
• No tamper claimed to be necessary. But consumers have repeatedly requested tamper availability – See Universal Tamper.

Advantages of Alterna Jars

• Offers good retrofit on multiple blending machines of high-performance, including those from Vitamix, Blendtec blenders, Waring and JTC Omniblend, few among others
• Sits straight onto Blendtec, and on Vitamix, Omni, Waring 3.5HP and Good4U blenders in angel perpendicular 45 degrees turned
• Gears modified in various dimensions for correct fitting into applicable blenders
• Capable of producing diverse concoctions and blends like smoothies, ice cream, hot soups, sauces, sorbet, purees, rice, paste and broccoli and ice cubes among others. Improves blending quality especially with nut butters, strawberries, raspberries, blackberries, and other real hard to emulsify ingredients that would otherwise leave visible particles
• Features replaceable blades compatible with Blendtec, Vita-Mix, Omni and Waring blenders

Selecting the correct blade-cutting assembly unit enables users of Alterna jar to achieve convenient blending operations with their blender.

By Alterna Jar (C) 2015

Blendtec Blenders fix Blades - Alterna Jar with removable blade June 16 2015

The Orem Utah Blendtec company makes great blenders. They are very powerful blenders and blend efficiently. Blendtec blenders themselves will outlast their jars and blades by many years. Blendtec blenders are commonly known for its high quality textured blending. Tom Dickson, the CEO of the company, is well-known to blend up ipods, phones and rocks or diamonds with his successful "Will-it-Blend" blending presentations posted on Youtube. Blendtec's latest jar success is the twister jar; before it was the wildside container and the regular fourside jar.

The wildside jar used to be known as the 5-side jar or 3 quart jar. It surely has 5 patented sides, but it was never really or truly a 3 quart 96 ounces container. The blades, there are 2 knives, one on each side of the axle, are dull and turn counter-clockwise. If the blade bushing, note - it does not have bearings- wears out and seizes up, users have to replace the entire complete jar. This is because the blade assembly unit is fix installed and cannot be removed or exchanged like with the famous Vita-Mix design. Vita-Mix and Blendtec are arch rivals when it comes to tamper usage and application and removable exchangeable blades versus fix-installed blades. Vita-Mix also turns the blade counter-clockwise and their blades are sharped.

A Blendtec fourside jar runs about 70 to 80$ dollars, a Blendtec wildeside jar runs about $95 to $110 dollars. Vitamix blade assemblies cost about $ 65 to $70 dollars while their jar complete with blade is exorbitantly 150$ dollars expensive. These are USA prices. In other markets such as Australia or Brazil, Blendtec Jars are at least twice as expensive as here in the USA and Vitamix jars cost at least 50% plus over the US.

If you have a Blendtec blender as a consumer with a US 7 year warranty (Europe for example provides a 3 year Total Blender Blendtec warranty), while still on warranty, if you happen to experience a blade bearing / bushing seizing up, Blendtec is usually very accommodating (Not in Europe, Brazil or Australia though). Just give them a call, if you can, and they will send you a new container if your initial  blender purchase is still under warranty, of course. If your warranty has expired, you are looking at having to purchase a new jar. With Vitamix you just buy a new blade and swap that out. This is one of the reasons why many consumers and shop operators buy the Vita-Mix type (also the Warring or Omni) blenders in the first place.

Restaurant or commercial use warranty of Blendtec Blenders is in the US 1 year. Restaurants use the jars more than ten thousand times per year. Therefore the blade bushing wears out faster in a restaurant / commercial application over a household consumer usage. Go to for example your local restaurant equipment supply store where restaurant and smoothie shop operators usually buy their equipment and restaurant supply from and ask them what the biggest draw-back for Blendtec blenders is. They will tell you that many of their commercial customers go through a lot of Blendtec jars every year because you cannot switch out the blade assembly. This is very expensive for these business people because they have to buy all whole new complete jars every time.

Now, this is the question that we propose -and we have already the solution for it as well:  What if consumers and commercial operators could purchase a Blendtec blender container that has a better and removable / replaceable or exchangeable blade unit cutting assembly? What if there was an alternative jar and blade solution to the Blendtec blender smoothie application? What if the blade bearing were to wear out for example, and instead of having to buy a whole new jar, you could just replace the blade assembly for your Blendtec blender, just like you could do with your Vitamix?

To take it a step further, Alterna Blender Jars and Blades makes one and the same blender container to fit on Blendtec blenders, also to fit on Waring MX1050XT (and alike 3.5 hp extreme blenders), on the JTC Omni Blender, and Vita-Mix alike type blenders (also the Good4U)... just swap out the blade for the different direction and different size of gear.

Blendtec jars and blenders do not come with tampers. Vitamix blenders however do. Alterna makes a universal tamper specifically for the Alterna jar for your Blendtec blender application.