I could be talking about healthy foods this time. But what our business is really about is healthy equipment so you can blend up your healthy foods. You have already a great blender, either that being a Blendtec, Vita Mix, Waring, or an Omni blender.
Blenders don’t easily break, but the blades and jars wear out. Sometimes blades wear quicker. So let’s go over a few things to help you extend the life of your blender blades and jars, regardless of what brand of a blender you have.
Problems and solutions (most common) that could arise during blending:
- Blade bearings (and bushings) can seize up - Rinse and dry by hand only
- Jars can crack - Keep bottom plate tightened
- If you blend heavy low-water-content ingredients (puree) you can get temporarily stuck or have a little delay getting the vortex / swirling of the smoothie miracle going - Use a tamper or when blending smoothies, make sure the solids to water ratio is right for the vortex
Problem 1: When you over-expose a blade bearing of your blender jar to water too much, water gets
into the blade assembly housing and will wash out grease. You will see rust powder coming out on the bottom end of the blade assembly at the gear seal. This leads to damage to the bearings which then will not turn smoothly anymore. Bearings are getting hot already when they are in good condition. They become much louder and hotter when there is more friction due to bad bearings. This will lead to oil exit on the bottom outside of the where the gear sticks out of the blender container. When the blade seizes it can also transfer energy to the drive socket and snap it or strip it (Drive socket is on the blender motor).
With the Blendtec blender jars (Wildside, Fourside, Twister), as the picture above left indicates, the 
blades are permanent fix installed. If that breaks, you cannot just change the blade assembly, but you have to change the entire jar. There is a big advantage if you have a jar with a removable blade assembly because you just change the blade – see to the right – if you run into a problem. That said, there are in both cases preventative solutions that can help you preserve the blade assembly bearing and help you get more usage out of it
Solution 1: Always wash or rinse the blender jar by hand and then dry by hand to limit water exposure. For additional sanitizing, use a non-caustic water-diluted spray on sanitizing solution to briefly apply to the inside of the jar. Don’t leave jar in sink with water puddle or wash in dishwasher. If your blade has seized up, or shows signs of seizing (roughness of turning, noisier blending, smoke / smell), replace the blade right away to prevent further damage to the driver socket.
Problem 2: Jars, if they do crack, they mostly crack on the very bottom around the hole where the 
blade assem
bly inserted into the jar. This occurs mostly when the blade assembly is starting to seize up or has already seized and you keep blending with it and in addition the bottom plate may not be completely tight, or tight enough.
Solution 2: Make sure the blade assembly works well and there is no rust around the gear. If there is and/or you experience leakage on the bottom, immediately remove the blade assembly and inspect the jar and the blade. Replace the blade if the jar is still good. Or else replace the whole jar with blade. We do have new better working blending jars with sharp efficient advanced blending knives. Frequently check the bottom plate to see if you can manage turning it clockwise to tighten it, to make sure it stays tightened.
Problem / Solution 3: Simple, if you get stuck or your blender has a hard time getting the ingredients blended or started up, either add more liquid, or if liquid is not part of your recipe, use a tamper stick specifically designed for the use with your blender jar. In our case, we have a Univers
al Tamper that can be adjusted to work with any blender jar, from Blendtec to Waring or Hamilton Beach. Make sure you use the tamper to push down on ingredients with the flanges positioned correctly to avoid touching the blades and only inserting the tamper through the lid hole with the cap removed, the lid on the jar, of course.
If your Universal tamper accidentally touches the blade knives during blending, this is not a serious problem for the tamper. The material is a food grade FDA approved material, but it is not edible. You will lose your smoothie. But you can save the tamper with sand paper and/or a saw. The Universal Tamper is solid.
If the flang
es come apart, use tape to secure the flanges. If you use a wooden tamper it will splinter into oblivion unfortunately and if you use a tamper made with injection molding plastic, it will break and not be usable anymore. If you do not have a tamper, I suggest you get one, even if think you never need one or needed one before. It takes only one time of difficult blending when you lose your hand or your fork. Never insert a fork, knife, or spoon into your blender jar during blending to push down on ingredients.
Even blenders made to work well without the use of a tamper need a push every now and then. And if you have a blender from a factory that recommends regular usage of a tamper to eliminate their air pocket, you will find,
with the right solid – to – liquid ratio, you do not need to use the tamper.
Please check out our new Alterna Jars, sharp blades, advanced finer better smoother blending, interchangeable between Blendtec – Vita Mix – Waring – Omni, etc… blending volume of 80 ounces. Now available with a $10 OFF discount. Use Coupon code $10AlternaOFF (use with purchase $80 and up – good till supply lasts and/or subject to be discontinued without notice)
If you have any questions, feel free to contact us by phone 801-623-3225 or by email customerservice@alternajar.com.
Thomas Fox
www.alternajar.com
801-623-3225
Blendtec wants to do everything in opposite Vita Mix does. Vita Mix blenders turn counterclockwise, so Blendtec motors turn clockwise. Vita Mix uses, even promotes, the safe use of air pocket eliminating blending accelerator tools (aka plunger or tamper). So Blendtec's Tom Dickson calls them silly (on Youtube), and in opposition promotes a blender and jars (especially the Twister) that do not need apparently a tamper "plunger". Vitamix has sharp blades, so Blendtec professes blades blend better when they are dull.
Really?
Sharp knives really cut better. Have you ever cut yourself on a dull blade edge? Can you cut an apple better with a dull or a sharp knife? Is a Samurai Sword dull or sharp? Is a circular saw blade dull or sharp? Do you know what happens when a circular saw blade is dull and you cut yourself? It pulls in your whole limb and rips it off instead of just a nice clean straight cut. Do you know what happens to wood when you cut with a dull blade? It is ripped to pieces with an ugly looking finish edge and splinters flying.
Get the point?
Sharp is definitely better:
A sharp knife in a blade assembly inside a blender jar cuts ingredients much finer and smoother. Blending goes faster, it is faster better tasting too. No logic question about sharp, just like with the logic behind that a blender apparently never needs a plunger tamper ("Blendtec friends"), while we sell a ton of tampers for Blendtec Wildside and even for the use with the famous Twister jar. Why would consumers buy tampers if they are not needed?
No need to be all about Rebel. By the way the Rebel Jar is a jar made by Blendtec to fit onto the
Vitamix blender, an idea taken from 123Vita LLC in 2010, really nothing so rebel about when a company like Blendtec actually just rebels against common sense and all logic.
Blendtec makes good Blenders. The fight against everything that Vitamix does is childish. We make the real Rebel Jar, the Alterna Jar with replaceable blade assembly and the knives are really sharp, as sharp as a Samurai Sword.
The same jar fits multiple blenders, like the Vita Mix, Omni blender, or the Waring MX series of blenders, and all Blendtec blenders of course. And we offer a tamper for those who blend puree and nut butters. It's common sense. When you need it you are glad you have it.
(C) 2015 - 2016 Thomas Fox / Alterna Jar LLC
Blenders from Vita-Mix come along with a tamper accelerator tool, whereas Blendtec and Waring do not offer it. Officially advertised, the blending cycles of Blendtec blenders exclude the need for a tamper accelerator tool, and Waring chooses not to avail one to customers. Certain consumers however find it necessary having a tamper present sometimes. Others prepare their smoothie, purees, nut butters, creams, and soups with intent of using a stirring tamper tool.
While Blendtec is stating as a marketing type method that no tamper is needed, in various cases it is more than handy to have one available because if you do get stuck with your food then it is safer to have one than for example using a fork or spatula to give the ingredients a quick push-down to get the blending motion going.
Different names are assigned to a tamper, relative to its manufacturer, whether from Blendtec, Waring or Vitamix in this case. A majority of individuals refer to it simply as a tamper. This important tool is used for pushing down ingredients to the upper proximity of the blade level, but with some safe distance, to achieve accelerated blending process of content such as raw soup, puree, nut butters, or smoothie. Utilizing an accelerator tool moves ingredients forcefully towards this blade, which rotates at extremely high speeds.
Vita-Mix Accelerator Tool is made from a polycarbonate type plastic comprising a lid hand which closes off the hole formed inside blender container lid while in use. The tool moves freely in and out of the container. Downward action of content creates vacuum action which sucks it into the container as blending takes place. Vita Mix recommends that one use their Accelerator tool throughout the process of blending to expedite the action. Their so-called patented accelerator tools to vacate air pockets are almost needed all the time as per Vita-Mix advertising. But air pockets according to a lawsuit between Vita-Mix and Basic and its follow up appeal confirmed that Vita-Mix however was unable to successfully proof air pockets. One could simply add more water to the ingredients and create the vortex action. But you don’t always want a more liquid concoction.
Certain retro-fitted tamper tools are available in the market. Some blender operators also prefer using a plastic tool or wooden dowel for pushing down towards the blade in rotation to accelerate blending operation. As a result the tamper gets blended up and/or damaged. This could be due to use of an appropriate Accelerator tool with lid in place. If one were not to use a tamper tool appropriately with lid in place, say, for example a fork or knife, or even a hand, pushing down on ingredients that way in high performance blenders could lead to very serious injuries, amputation, and/or damage to the blender units and blades.
Blending Soups and Purees with or without Tamper
When preparing ingredients for smoothies or soups, water is normally added. A tamper may not be necessary to use while blending the content, if sufficient liquid or water is added to the other raw ingredients. A hollow cave area appears just above the blade only when excessive amount of ice is applied for the smoothie process, with the blender cycle turning too fast. Blendtec blenders like the HP3A or Total Blenders are designed with the versatile blending programs it operates, which eliminate the necessity of using a tamper, supposedly. It is “supposedly” because this claim is not always true. There are just too many variables in blending that could be the amount of ingredients, how they are placed, which one first, what consistency they are, what the liquid to solids ratio is, if there are some obstructions like large ice section, and the timing of the blender, the blender motor strength and momentum of turning and starting up, etc. Still, one may require some type of tool to push down the blending ingredients, maybe for stirring, maybe just enough of a push to get the blending action going. Once it is running, meaning you see all the ingredients cycling, the blades will do all the rest of the blending by themselves.
Less amount of liquid is used when preparing a pate or puree in a high-performance blender. One may as well require some form of device for pushing down contents to the blade level. Blendtec especially makes its blenders to operate without needing an accelerator tool or tamper. However, consumers report using cutlery and other equipment to push down the ingredients.
Especially when making nut butters (i.e. Almond butter), a tamper tool is mandatory. The nuts are too heavy and oily, so they are sticky, they just will not freely circulate with the blade turning action. You need to help it to move along and turn over the massive almond puree until it gets oily and is ready for consumption.
The Universal Tamper Accelerator Tool made by Alterna is a great device which fits into any blender jar. Some exceptions exist, like for the Ninja, which lacks the blade construction appropriate for allowing tamper-insertion. The Ninja’s blade is really like an auger that does not let the user insert the tamper. The universality of the Alterna tamper means that it literally can be adjusted and set at different height levels from the area where the tamper is inserted into the jar through the hole in the lid. This adjustability is important to make sure that the tamper will never touch the turning blade during operation when inserted into the jar. Different blender styles and brands have different dimensions from the hole in the lid down to the tip of the blade.
Acetal Delrin, the material employed in making this tamper is approved by FDA “for food contact.” As a precautionary measure, the 2 pieces of flanges (rings) are clamped around the location desired, fitting the tamper in firm manner, the location being the adjustment area that determines the remaining length of the tamper end that is being inserted into the lid cap hole, reaching down towards the blades. This keeps the low tamper-end from touching the blades once inserted through the lid.
The Alterna tamper can fit into Vita-Mix 64 ounce containers, the 32 oz jar, Blendtec Wildside or Fourside, all the Waring and Hamilton Beach blenders, and Kitchenaid, Cusineart, Oster blenders. You name it, if the blender has a jar with a removable lid cap and a regular type blending blade cutting unit, the Universal Tamper come universally adjustable in as a very handy tool. It is apparently better to have it and not need the tamper, than needing it and then using a fork or worse, your hand.
Wood tamper dowels too are becoming quite popular to be used as tampers. They are relatively inexpensive and easy to make when one has a drill machine. Just cut the dowel to length between 8 to 12 inches, usually a dowel with a diameter of 1 inch. Drill in a hole of 3/8” where the appropriate location of the stoppage cross rod should go through to prevent the dowel from entering the jar through the opening in the lid. This cross dowel will prevent the dowel ‘hopefully’ from touching the blades during the blending action. Otherwise, if the wood dowel touches the blades, it will splinter severally making the dowel unusable for future blending actions. Wood also has the likely tendency to absorb water and is therefore very insanitary.
Some people like wood better over plastic, because if by accident one were to blend in untreated wood into ones smoothie, the smoothie would at least still be somewhat edible, subject to one’s appetite. Of course if plastic is blended into a smoothie, you would have to through it all away, for sure. The Acetal Delrin material does not splinter much and therefore unlike with the wood and the completely shattering hollow plastic tamper, Acetal Delrin (POM) is a solid compressed high density material that will be rendered reusable as a tamper stick. From that aspect, and because POM has been used for food processing in food contact for decades, it is an ideal material for the food blending applications as a tamper accelerator tool.
into the blade assembly housing and will wash out grease. You will see rust powder coming out on the bottom end of the blade assembly at the gear seal. This leads to damage to the bearings which then will not turn smoothly anymore. Bearings are getting hot already when they are in good condition. They become much louder and hotter when there is more friction due to bad bearings. This will lead to oil exit on the bottom outside of the where the gear sticks out of the blender container. When the blade seizes it can also transfer energy to the drive socket and snap it or strip it (Drive socket is on the blender motor).
blades are permanent fix installed. If that breaks, you cannot just change the blade assembly, but you have to change the entire jar. There is a big advantage if you have a jar with a removable blade assembly because you just change the blade – see to the right – if you run into a problem. That said, there are in both cases preventative solutions that can help you preserve the blade assembly bearing and help you get more usage out of it
blade assem
bly inserted into the jar. This occurs mostly when the blade assembly is starting to seize up or has already seized and you keep blending with it and in addition the bottom plate may not be completely tight, or tight enough.
Solution 2: Make sure the blade assembly works well and there is no rust around the gear. If there is and/or you experience leakage on the bottom, immediately remove the blade assembly and inspect the jar and the blade. Replace the blade if the jar is still good. Or else replace the whole jar with blade. We do have new better working blending jars with sharp efficient advanced blending knives. Frequently check the bottom plate to see if you can manage turning it clockwise to tighten it, to make sure it stays tightened.
Problem / Solution 3: Simple, if you get stuck or your blender has a hard time getting the ingredients blended or started up, either add more liquid, or if liquid is not part of your recipe, use a tamper stick specifically designed for the use with your blender jar. In our case, we have a Univers
al Tamper that can be adjusted to work with any blender jar, from Blendtec to Waring or Hamilton Beach. Make sure you use the tamper to push down on ingredients with the flanges positioned correctly to avoid touching the blades and only inserting the tamper through the lid hole with the cap removed, the lid on the jar, of course.
with the right solid – to – liquid ratio, you do not need to use the tamper.
Vitamix blender, an idea taken from 123Vita LLC in 2010, really nothing so rebel about when a company like Blendtec actually just rebels against common sense and all logic.
